Відео

Just got this part. it says you're supposed to install it with a new stainless steel male center roller. Without the new roller it can results in incorrect door operation. I have a 2014 odyssey. Is this necessary?

Thank you sooooo much. For 3 years we struggled with our range. Just fixed it and we’re at 325 in 4 mins!

My front panel won’t go back on wtf

thank you for posting this. same exact problem with our drier.

Thank you very much! Took me longer to make sure I had the right model number than the repair. Oven went from 35 minutes to get to 425 to 5 minutes😀 seriously dude, keep up the good work!!

My daughter has a newer one . Has anyone tried this before?

Thanks so much you made it totally an achievable undertaking for me

Just put the new part in! 7 minutes to heat up! Thanks for the help.

This is a good fix, but ONLY if you have enough clearance to the underside of the countertop.

Saved me a G brother. I was about to buy a new dryer when I saw this video and said "hmmm, lemme check see if the belt is loose like that." The rest is history. If you're ever in Toronto, beers on me lol

I can not for the life of me find a spring 😢

nice. 1) after you removed that exhaust tube, did you removed the rear panel? Seems like you had a lot of view and access from just the little area. 2) how did you know the belt serpentine like that?

Thank you!

Is there a mechanical closed lock so that you can just cut the cables and open/close the door manually? I wish they still made the sliding manual doors like back in the day.

Thanks you helped me understand what was wrong and how it get it right again! Happy 4th 2024

Brand new Stihl chainsaw - wouldn't turn off. Took it back to Stihl dealer and he showed me the issue. However 80% of the time i use it, the switch would stihl pop out of its cradle, and the spring would fall below and wouldn't make connection and won't turn off. I would pop the top off and disconnect the spark plug to stop it. Very annoying.

Don’t know if you’re still reading the comments but thank you so much!! Just replaced ours following your video took no time at all and oven is working perfectly again!! We appreciate you taking the time to make this video!

You can repair it this way, much less time consuming than tearing the dryer down from the front. However a bit of advice, lay a cloth down over the metal edges of the hole you are working through. Those metal edges are really sharp, trust me. I found out the hard way with several gashes on my forearms.

Great video! Thanks! Question - At approximately 18:18 on the video the left side cable seemed loose. Did you have to re tension that before locking down the assembly down or did it correct itself?

My power cord doesnt want to come off my power Jack.. are they all like that? Think I’m gonna have to return this rack.

Thank you my ZR2 Colorado was on the chopping block

Tried this and it it worked. Engine sounded as if it was under load, voltmeter perked up and held steady, so I hooked it up to the house and everything was fine, for about 5 minutes. Trying this again didn't have the same results - the engine groans and the generator breaker flips after about 2 seconds. Is the generator fried?

kool

What is the "snail shaped device" called . Someone with a father help me out

The sensor that detects the key is what goes bad .. if you replace that the problem goes away

I did almost the same things. I did not separate the metal frame and faulty digitizer from the larger glass screen because the metal frame is easily bent. All other actions were the same. Been two days and so far it works like new.

Good information. Thank you. I have owned many homes of my own as well as owning several rental properties. I can say, without question, that I have consistently had bad experience with Samsung appliances. They make good TVs and phones but not good appliances.

Excellent! This fixed my issue easily.

WOW literally the smallest lil 0.2second squirt of WD-40 up into the pull chain hole and a few tugs and its fixed.

Nice 👍

Excellent video. Thanks for the link.

Thank you so much for video everyone else was taking it completely apart this was detailed and great and saved me so much time. Really appreciate it ❤

Thank you for sharing your knowledge! I was able to fix my family’s dryer thanks to you!🙏🙇🏻🙇🏻🙇🏻🙇🏻

Thank you for this video!! I fixed the ceiling fan within my dining room! I was going to purchase a whole new fan; but decided to see if replacing the part was something I could do myself. I found your video and I fixed it myself by following your instructions! I appreciate your video being very step by step, clear, and direct! Thank you! 😊

Nicely done

I am having trouble removing the snail shaped device. Does it unscrew? Do I just need to twist harder? I don’t want to break it.

Will this screen part no. fit my 2019 Silverado 3500 HD LTZ? Thanks

Yall forgot that it's another filter in that top cabinet

Question: when you go back to re assemble everything. And fit the pipes back together. (Female, male part) Do you need to untighten thay screw on that part and retighten it once connected? Reference 8:17. Thankyou!

Why didn’t you show battery connections you made, particularly the connection with cables to the generator

Thanks mine was doing same thing and your video helped me. Thank you Got it running perfect now.

Why not unscrew the snail part apart into its 2 halves so the wires don't have to be cut?

PERFECT QUICK AND TO THE POINT VIDEO

My Black kill wire kept separating itself from its guide and would pull away from where it should have been, thus not in position to be grounded out. Wiped both down with alcohol, let them dry for a couple minutes and put wire the back in the guide. Placed one drop of Loctite Super Glue on them, let them sit for a few minutes and they haven't separated since. PLEASE KEEP IN MIND, IF YOU DO THIS, IT IS PERMANENT. hth

So if door won’t open or close, You need to cut the cable and you will be able to manually open and close it in the meanwhile?

What were the part numbers?

Very useful thanks a lot

Unless the drill has a permanent magnet motor the drill method is not going to work.

If I spin in myself and starts the spin, could it be the same thing?

Awesome video thank you, but I have a BIG favor to ask Could you reference one part of your video that shows where that damn piezo electric buzzer is located. Research suggests it's someone on the motor assembly? My doors are working fine but the buzzer won't stop and from putting my ear up to the rear panes it's coming exactly from where this motor actuator is located. Thank you.